Questions without answers in Mechanics of deformable bodies

At the peak (also denoted as UTS) of an engineering stress vs. engineering strain curve for ductile metal, the engineering strain is $0.2$. The corresponding true stress ...

Which among the following options is/are CORRECT unit(s) of stress?$\mathrm{Nm}^{2}$$\text{Pa}$$\text{Nm}$$\mathrm{N} / \mathrm{m}^{2}$

A $\text{2D}$ state of stress at a point in a body is given by $\sigma_{x x}=-40 \mathrm{~MPa}$, $\sigma_{y y}=100 \mathrm{~MPa}$ and $\tau_{x y}=50 \mathrm{~MPa}$.The ra...

Sum of the principal stresses of a $\text{2D}$ stress state $\left[\begin{array}{cc}11 & 4 \\ 4 & 5\end{array}\right]$ is $\_\_\_\_$ (in integer).

One column with square cross section of side $r$ and another column with rectangular cross section of breadth $p$ and width $q(<p)$ are made from the same material. Both ...

Two prismatic rods of identical lengths are designed for the same strain energy density when subjected to the same axial load. One of the rods is made of steel (Young's m...

A $\text{2D}$ stress state of pure shear is shown in the figure.Which one of the following options is equivalent to the given stress state?Figures are not to scale.

The bending moment diagram for a simply supported beam is piecewise linear as shown in the figure. The bending moment $M(\mathrm{x})$ at $\mathrm{x}=0.5 \mathrm{~m}$ is $...

A thin walled cylindrical container of diameter $2$ $\mathrm{m}$ and wall thickness of $2.5$ $\mathrm{cm}$ is made of steel whose Young's modulus is $200$ $\mathrm{GPa}$ ...

A solid axial bar made of steel with Young's modulus, $200$ $\mathrm{GPa}$ and Poisson's ratio, $0.3$, is subjected to uniaxial stress of $50$ $\mathrm{MPa}$.The absolute...

$\text{EFGH}$ (solid lines) is the initial configuration and $\mathrm{E}^{\prime} \mathrm{F}^{\prime} \mathrm{G}^{\prime} \mathrm{H}^{\prime}$ (dashed lines) is the defor...

A simply supported beam of length $l=2 \mathrm{~m}$ is subjected to a concentrated moment $M=150 \mathrm{~kNm}$ at a distance $l / 2$ from the left end as shown in the fi...

A rectangular plastic specimen with a cross-sectional area of $240 \mathrm{~mm}^{2}$ is subjected to tension with a force of $15000$ $\mathrm{N}$ resulting in elastic def...

Consider a spring-mass system with mass $m$ and spring stiffness $k$ as shown in the illustration. At time $t=0$, the mass is displaced by $P$ units and the velocity of t...

​​​​The Mohr's circle corresponding to an infinitesimal element is shown in the figure. The plane $\text{PQ}$ in the infinitesimal element, at an angle of $\theta$ from t...

The two-dimensional state of stress, in an infinitesimal element, is given by$\sigma_{x x}=800 \mathrm{MPa}, \sigma_{x y}=300 \mathrm{MPa}$ and $\sigma_{y y}=0 \mathrm{MP...

Consider a beam with a square box cross-section as shown in the figure. The outer square has a length of $10 \: \mathrm{mm}$. The thickness of the section is $1 \: \mathr...

For a certain linear elastic isotropic material, the Young's modulus is $140 \: \mathrm{GPa}$ and the shear modulus is $50 \: \mathrm{GPa}$.The Poisson's ratio for the ma...

​​​​Which one of the following vertical columns, of circular cross-section, sustains the highest load without buckling?Cantilever column with a length $\text{L}$ and cros...

A closed thin cylindrical tank with a mean diameter $\mathrm{d}=300 \mathrm{~mm}$ and thickness $\mathrm{t}=2 \mathrm{~mm}$, is subjected to a uniform internal gas pressu...